상품명 | [CoolTech] RFA16 16CH FASST Compatible Receiver HV - 후타바 호환 수신기 |
---|---|
판매가 | ₩57,000원 |
적립금 | 1,710원 |
제조사 | Cooltech |
수량 | 품절 |
수량 |
SNS 상품홍보 | |
---|
(최소주문수량 1개 이상 / 최대주문수량 0개 이하)
[CoolTech] RFA16 16CH FASST Compatible Receiver HV - 후타바 호환 수신기
- CoolTech 사의 후타바 FASST 방식 호환 수신기 입니다.
- 검정된 제품으로 전동기,헬기,자동차,보트 등에 사용하시면 됩니다.
- HV (High Voltage) 사양으로 3.5v~8.4v 까지 사용 가능합니다.
- 메뉴얼 바로가기
- 바인딩 방법
1. 조종기 전원을 켠다. (조종기 수신방법은 FASST-MULTI로 지정)
2. 수신기 버튼을 누른 상태에서 수신기 전원을 공급한다.
3. 수신기에 빨간불빛이 사라지고 초록색으로 고정되면 바인딩이 완료.
- FS 와 HS 모드 변경방법
1. 조종기 전원을 끈다.
2. 수신기에 전원을 공급후 F/S 버튼을 6초정도 누릅니다.
3. 빨간불빛이 빠르게 깜빡이면 HS 모드, 천천히 깜빡이면 FS 모드
SPECIFICATIONS:
Operating Voltage Range : 3.5~8.4V
Dimension:46.7X14.6X36.8mm
Weight:17g
Latency:14ms(LS)
:7ms(HS)
Sensitivity:about -96dBm
INTRODUCTION: (호환조종기)
Cooltec 2.4GHz Spread Spectrum FASST Compatible Receiver is designed to use with FUTABA FASST 2.4GHz Air System(7CH Mode/Multi Molde), such as TM7, TM8, TM10, TM14 or T6EX-2.4G, 7C-2.4G, 8FG, 10CG, 12FG , 14MZ, 14SG, 18MZ.
BINDING PROCEDURE:
Turn on the transmitter, get to the LINKAGE MENU - SYSTEM and select FASST-7CH or FASST- MULT, Connect
battery to the receiver while holding the F/S button on the receiver, the red LED on the receiger is off and green LED constant on indicates binding successfully.
SETTING FAILSAFE:
RFA16 support two delectable failsafe setting options, either use native failsafe position preset on transmitter, or set failsafe on RFA16.
1) Use native failsafe position preset on the transmitter side:
If not disabling failsafe on the transmitter side, RFA16 will use native failsafe position preset on the transmitter side.
2) Set failsafe on RFA16:
RFA16 supports failsafe function for all trannels. Follow the steps below to set failsafe positions for each channel.
(1) Bind the receiver first and disable failsafe on the transmitter side;
(2) Set all transmitter controls to the desired failsafe position;
(3) Press briefly the F/S button on the receiver(less than 1 second), the green LED will flash twice, indicating the failsafe is set up successfully;
(4) To disable the failsafe fuction, just need to rebind the receiver.
HOW TO SWITCH BETWEEN LS AND HS MODES:
Turn the transmitter off, connect the battery to the receiver, press the F/S button of receiver for 6 seconds and then release. The red LED will flash fast in HS mode and slow in LS mode. Reapeat this to alternate modes.